I was unable to find a standard landing gear that was used on the 2003 Keystone Challenger model campers, so I will not have a direct replacement. That being said, this does not mean we don't have an option available.
The Bulldog Tandem Landing Gear Set # BD500162 will have a bracket height difference of 17 1/2 inches. This will be measured from the bottom of the upper bracket to the top of the lower bracket. This can also adjust from 36 inches wide to 70 inches wide and is rated to 8,000... view full answer...
I confirmed with Curt that the correct replacement shank for Curt TruTrack Weight Distribution System w/ Sway Control - Trunnion - 15,000 lbs GTW, 1,500 lbs TW # C17501 is the Curt Adjustable Weight Distribution Shank - 8" # C17100. I attached a short demonstration video for you to check out. view full answer...
The # LC719324 Flow Max faucet doesn't have replacement aerators available so you would need to replace the whole unit. I have attached the page with our faucets for you to choose a new one. If you want to choose a different brand that does offer replacement parts the Phoenix brand faucets like # PF221403 offer replacement aerators incase you ever have another issue and don't want to have to replace the whole unit. view full answer...
The Draw-Tite Trailer Hitch Receiver # 36416 for the 2007 Toyota Camry will use the following hardware.
Qty. (4) M10 X 40 X 1.25 CL8.8 Hex Bolt
Qty. (4) 3/8” Conical Toothed Washer
Qty. (2) 1/2-13 X 2.00 GR 5 Hex Bolt
Qty. (2) M10 X 1.25 Hex Nut
Qty. (4) Block 1/4 X 1.50 X 3.00
Qty. (2) 1/2” Lockwasher
Qty. (2) 1/2” Hex Nut
Qty. (2) 7/16 Washer
We do offer a Replacement Hardware Kit for Trailer Hitches # RHK that you can order to receive all the correct hardware that you need. You will... view full answer...
We can definitely get you replacement hardware for the Curt # C11066. The # RHK can be matched to any hitch that we carry and all you will need to do is put in the part number you need the replacements for ( # C11066 ) and the manufacturer of the hitch (Curt). We will then assemble all the needed pieces and ship them out to you. I did include a picture of all the hardware that comes with this hitch as well. view full answer...
According to Dexter Axle, your 3K Dexter Axle uses the # LM67048 inner bearing, the # LM67010 inner race, the # L44649 outer bearing and # L44610 outer race. For a replacement grease seal, use # 58846.
If your brake magnets or pads are worn, you can replace the brake assemblies using the Dexter 10 x 1-1/2 inch brake assemblies, part # K23-472-473-00 which include the left and right brake assembly as well as mounting hardware and the mud and crud plugs. view full answer...
With the typical ST235/75R15 tire having a diameter of 28.8 inches (roughly), the Westlake ST205/75R15 Radial Trailer Tire - Load Range D # LHWL300 at a 27.1 inch diameter, will definitely fit your 2017 R-Pod 177. These will have a maximum capacity of 2,150 pounds at 65 psi and an L speed rating (75 miles per hour).
As to rim Aluminum Sendel Series T02 Machined Trailer Wheel - 15" x 6" Rim - 5 on 4-1/2 # AM22653 would be a great look. This is a 15 x 6 inch rim with a 5 on 4 1/2 bolt pattern. view full answer...
To replace your Fan-Tastic 6000BTA I recommend using the Fan-Tastic Vent Roof Vent w/ 12V Fan and Thermostat - Powered Lift # FV803350, which has a powered lift and 3 speeds. If you wanted something with a manual lift the Fan-Tastic Vent Roof Vent w/ 12V Fan and Thermostat - Manual Lift - 14-1/4" x 14-1/4" # FV802250, which is the same fan only the vent lifts manually instead of powered. Both of these would fit in the opening left by your existing Fan-Tastic Vent 6000BTA on your 2007 Gulf... view full answer...
The Gustafson RV Scare Light # 277-000485 is the correct size and has a clear lens but it does have a black base. This is the only light we currently carry that is the same shape and size as the light you have on your 2016 V-Lite trailer. view full answer...
The replacement hinge seal you need for your Extang Encore tonneau cover is the Replacement Hinge Seal for Extang Encore Tonneau Covers - Qty 1 # EX32620464. Each of these come with a replacement of 1 seal.
I went ahead and attached a video that shows the installation process of the seal. view full answer...
Thank you for the photo.
We may have a few replacement seal options for your Seal on 2001 SnoPro Clamshell Enclosed Trailer but you'll need to confirm the dimensions we have will work for what you're needing.
The Rubber Large Half Round Seal # SR26ZR measures 1/2" tall, the Rubber Bulb Seal # SR32FR measures 5/8" tall, and the Rubber Half Round Seal # SR85FR measures 11/16" tall.
These all have slightly different designs as well so you'll want to make sure these match or are close to... view full answer...
I reached out to Phoenix USA and was able to determine that the center cap of the Phoenix USA Rear Hub Cover # PXQ820R is part # PHX59FR. view full answer...
Yes, the Replacement Jack Handle for Ark Xtreme Off-Road Trailer Jack # ORJW750SH will work as a spare handle. This is a direct replacement for the handle on the # ORJW750D which is the same as your # ORJW750BD aside from the color. view full answer...
For your 2019 Grand Design you will want to use the MORryde Suspension Upgrade Kit # MR46ZR. The Kit # MR58ZR you found is for 5th wheels using the Correct Track system for aligning the trailer axles. This kit will allow you to replace all your shackles, wet bolts, and bronze bushings included with the Dexter EZ Flex # K71-653-00 in one easy kit. view full answer...
There are a couple options for a 30 amp, 90-degree female end to a power cord, depending on if you want the pigtail with wiring or just the actual plug. So you can choose from the following:
- Mighty Cord Replacement Hardwire RV Plug - 30 Amp Female # A10-R30VP
- Mighty Cord Replacement Pigtail for RV Power Cord Extension - 30 Amp Female # A10-30PFVP view full answer...
Yep, we have the exact replacement you need for your N197 key for your Sears cargo carrier; the correct part is the Replacement Key # THKEYN197. view full answer...
We do have a replacement hardware kit for the Draw-Tite Hitch # 75119. You will need the Replacement Hardware Kit for Trailer Hitches # RHK.
Make sure that in the pull down menus (below the Shipping Special box) that you insert your hitch number, 75119, and the manufacturer of the hitch (Draw-Tite) so that you get the correct hardware kit.
Pricing is available once you input all the necessary information. view full answer...
Your hub on your 2007 EZ Loader Custom trailer uses a unique size Grease Seal # 168255TB (inner diameter 1.687"). We do not have any bearing or hub kits that will have all the correct parts for your hub. Here is a list off the parts you would need to build your own bearing kit.
Inner Bearing # L68149
Inner Race # L68111
Outer Bearing # L44649
Outer Race # L44610
Grease Seal # 168255TB
If you would like to replace the hub that will already have the correct bearing races already installed,... view full answer...
There is not a specific kit that comes with the motor, blade, and ceiling vent cover for your exhaust fan V2062 so you will want to get those separately. You can go with Replacement 110-Volt AC Fan Motor # BCD0314-00 and Replacement Fan Blade for Ventline Bathroom Ceiling Vents - 6-1/2" Blade # BVA0312-00. I am not sure which vent cover you are needing, so I attached a link which shows you the various covers that you can choose from. view full answer...
We have the Furrion Chill Replacement RV Air Conditioner for Dometic Brisk Setup, # FR42PV. This is a 15,000 Btu unit that is compatible with ducted or ductless systems and will allow you to continue using the same thermostat and wiring you currently have. However, if you prefer to install an all-new set-up of AC and thermostat then I suggest the Furrion Chill HE RV Air Conditioner System, # FR55PV. This single zone, 15,000 Btu AC unit is for ducted or ductless systems, has a wall thermostat... view full answer...
Go To Results